#VCDS PROGRAM KEY HOW TO#
#VCDS PROGRAM KEY INSTALL#
#VCDS PROGRAM KEY DRIVERS#
#VCDS PROGRAM KEY UPDATE#
#VCDS PROGRAM KEY PROFESSIONAL#

#VCDS PROGRAM KEY HOW TO#

How to use BMW INPA software and cable K+DCAN

#VCDS PROGRAM KEY INSTALL#

How to install TIS2000 for GM Tech 2 scanner

#VCDS PROGRAM KEY DRIVERS#

Install BMW INPA on WinXP Win7 Win8 Win10ДЇree Download BMW E-sys V3.22.5 v3.2.61 v3.2.71ДЇree ECM Titanium 1.61 with 26000 drivers How to Install Toyota TIS Techstream 14.10.028 Passat B6 Comfort module component protection data

Instrument EEPROM: Decrypt for PIN, KM, and set new KM Note: Comfort module power class can change via adapt unit Input new Immo No, VIN, power, total 7 bytes CS, PIN, press button вЂњWriteвЂќ This usually happen for adapt original comfort module in car, because the comfort module have working key It requires input power class for 2nd hand moduleгЂ‚ДЄttention: the working key in 2nd hand comfort module will stop work after success reading, it can start work after write with correct 7 bytes CS. You can load EEPROM dump (95320) for 2nd hand comfort module, or type in known PIN/CS manually Instrument Cluster вЂ“ Magneti Mareli вЂ“ Shadow 2 (Passat) If you get вЂњYESвЂќ mean the immobilizer system use this type transponder Passat/CC lost all key, donвЂ™t know transponder type, Prepare a 48 transponder and a 46 transponder, insert to ignition switch one by one, verify вЂњTransponder type OKвЂќ. DonвЂ™t worry about вЂњLocked KeyвЂќ value, dealer key can be learned without test this item. If you get вЂњNOвЂќ mean ignition key is not dealer key. Passat/CC 46 Transponder learned key failure, verify вЂњDealer KeyвЂќ. VW Passat B6/CC with EDC17/MED17 вЂ“ CAN (Support OBD lost all key) VW Passat B6/CC вЂ“ CAN (Support OBD lost all key) Next time, try start with last failed times.Number 6 (Unlock 46 key)only unlock the temp key under try start method under decrypt failure method First try need start from 0, if failed in the procedure, record the failed times. Lost All key: this type need use try start method to find working key. No matter 48 or 46, no matter lost all key or add key, they are all same. You will get the 7 bytes CS and PIN after decrypt success. It has 3 methods to decrypt comfort module dump:Дecrypt 7 bytes CS from dump file (usually we select this method) After load comfort module dump you will get window Here you need comfort module dump (95320) support. Next time, try start with last failed times.Д¬annot read 6 bytes CS from ECU. Lost all key: this type need use try start method to find working key. Place 7th byte CS to вЂњFFвЂќДЄdd key: you need find 7th byte CS from working key, you can follow steps: 1->2->3->4 Lost all key is same as add key with working key. You can read PIN and 6 bytes CS from ECU via OBD, no comfort module dump IвЂ™d like to share the VVDI2 Passat User Manual: On VVDI2 go to Key learn-VW 4th generation then choose Passat CCM. Or if you have Xhorse VVDI2 you can do it with it as well, Nice thing about VVDI2 it will pop up message when Adaptation Ch is available. When you enter Pin you will have to wait 5 or 10 in before Adaptation Ch will become available. Like I mention above, write original dump back. Precode key with CS and program keys OBD with VCDS and all was good after that. There was a other member had same problem, So he wrote back original dump,

#VCDS PROGRAM KEY UPDATE#

I think Tango has BUG with last update for this. I have done both ways in Circuit and disolder chip and never had problem. Part 2: Both VCDS & Xhorse VVDI2: confirmed to program Passat b6 2007 all keys lost

Pull CCM, read and compare with file created by Tango. вЂ“ Anyway, higher chance that the final dump which he wrote to CCM might not been written correctly and itвЂ™s worth to check. I done couple and never had issues with Tango so always wonder what causes these. Or created new dump, wanвЂ™t written properly.Д«ecause I had same situation after someone tried to program keys with FVDIДЄnd all I had to do, was to write fixed eeprom to CCM and car started straight away on original key.ДЄnd this is not first situation when someone have problem after key programming by CCM dump. Maybe there was some difference in eeprom structure after your first reading. Upload it and IвЂ™m sure someone will fix it for you. I think CCM eeprom dump need to be fixed.

#VCDS PROGRAM KEY PROFESSIONAL#

What to do next? letвЂ™s listen to the professional locksmithвЂ™s advice: I checked TPвЂ™s in TANGO with the latest file, and they read as KEY 1 and KEY 2 Wrote new 2 key data back to ccm, and installed ccm,Д¬ar starts ONCE with key, immo active on dash, then wonвЂ™t start second timeД«attery disconnect, same again, starts once, not twice Removed ccm, read eeprom, put to tango, created 1 key, saved data, loaded that new file, created 2nd key, saved data Use Tango to program Passat b6 2007 all keys lost Tango: someone tested yes, someone tested no.

Vcds program key